Navigation & Audio Axxess AX-BM9112 Wiring Interface
#1
Axxess AX-BM9112 Wiring Interface
Anyone have one of these installed? It says it retains all the factory features (HK amp, steering wheel buttons, etc).
https://www.crutchfield.com/p_120BM9...Interface.html
https://www.crutchfield.com/p_120BM9...Interface.html
#4
#6
I ordered the AX-BM9112 from Crutchfield and wired it up tonight per directions. I have the HK system, radio turns on, but no sound. The harness isn’t complicated and all wires connected, but there is a whole section of wires from the factory harness that don’t have anything connected to it from the axxess harness. Was kind of hoping there would be more going on in this thread to help figure this out.
#7
Trending Topics
#9
#11
#13
#14
#15
I never did get the steering wheel controls working. I wish I could use it, but it's not like the head unit buttons aren't within fingers touch anyways. I still have the HK EQ button that's in the AXXESS wiring harness hanging out from the bottom, not sure where I want to mount it. I use it because it still sounds better than the head units EQ. I just leave the HU EQ flat and use the HK, but the only downside to it is you don't know which setting it is, you just have to listen for it because it doesn't display like it did on the factory HU.
#16
I seem to be where you were in your original post. I have power but no sound. I'm wondering if the amp is not getting a signal to turn on. I did not connect the Power Antenna wire on the radio. I also couldn't figure out what to do with the female jack from the kit (the one with bare Brown / Brown-White wires). I can see yours is commented to something in your pics but cannot tell what.
#17
#19
i’m starting to think
years are getting mixed up
I personally never used the steering wheel control modular
every time you disconnect the battery
you have to reprogram that modular
An those buttons really wasnt a big deal to me
If i remember correctly there are two different harnesses
With amps & with out amps
years are getting mixed up
I personally never used the steering wheel control modular
every time you disconnect the battery
you have to reprogram that modular
An those buttons really wasnt a big deal to me
If i remember correctly there are two different harnesses
With amps & with out amps
#20
I had the ‘no sound issue’ as well and yes the problem was the blue power antenna wire (it’s the one that is not connected from the harness) that has to be connected to the red wire.
means you have three wires connected to the red on in the end.
Anyway, it works perfectly now, steering wheel controls as well, thanks for the info
means you have three wires connected to the red on in the end.
Anyway, it works perfectly now, steering wheel controls as well, thanks for the info
#21
I have this harness and steering wheel volume and channel controls working fine. I have a 2005 R53 with the HK system. Question I have is that from the Kenwood head unit, if I fade to the back speakers I get no sound. So I use turn the fade to just the front speakers from the Kenwood and use the Axxess functions to work the fade front and back speakers. Sounds fine but curious why this is. Seems the factory head unit wiring harness has wiring for front and rear from the factory head unit. Shouldn't the aftermarket head unit be able to control fade?
#23
Thread
Thread Starter
Forum
Replies
Last Post
Navigation & Audio Axxess - ASWC now it works with R53!!
pew1375
Navigation & Audio
7
11-17-2019 01:30 PM
Navigation & Audio R53 (2004 MCS) Metra Axxess ASWC install help requested
Duaneo
Navigation & Audio
8
09-28-2013 01:24 PM
Navigation & Audio Steering Wheel Interface: Metra Axxess ASWC, PAC-JACK / PAC-SWI = FAIL!
Socially Distorted
Navigation & Audio
3
04-29-2012 03:58 PM
Navigation & Audio Blitzsafe Mini Interface Installation How-to by RSpeed
Mark
Navigation & Audio
11
12-21-2003 10:47 PM