JCW AC Schnitzer Front Splitter
#1
AC Schnitzer Front Splitter
Anyone know where I can get this splitter stateside?
http://shop.ac-schnitzer.co.uk/front...f56-6439-p.asp
http://shop.ac-schnitzer.co.uk/front...f56-6439-p.asp
#3
I've voiced my opinion on this splitter before. It's a dirt trap basically.
I would consider this one. It is a true piece of design not an afterthought.
http://www.3ddesign.jp/english/produ...INI_F55_56.htm
Thoughts?
I would consider this one. It is a true piece of design not an afterthought.
http://www.3ddesign.jp/english/produ...INI_F55_56.htm
Thoughts?
#4
I've voiced my opinion on this splitter before. It's a dirt trap basically.
I would consider this one. It is a true piece of design not an afterthought.
http://www.3ddesign.jp/english/produ...INI_F55_56.htm
Thoughts?
I would consider this one. It is a true piece of design not an afterthought.
http://www.3ddesign.jp/english/produ...INI_F55_56.htm
Thoughts?
#5
#6
$1600....hmmm. It is gorgeous & appears to be well engineered for sure...maybe if you live in flatland with good roads like Florida (where I used to live) I'd give it a whirl. My problem is if I went that route, I couldn't stop! Then would come cf rear diffuser, cf rear wing, cf mirrors & bonnet scoop.....etc. Ha! Still stock for now. I do love the new JCW! :-)
#7
$1600....hmmm. It is gorgeous & appears to be well engineered for sure...maybe if you live in flatland with good roads like Florida (where I used to live) I'd give it a whirl. My problem is if I went that route, I couldn't stop! Then would come cf rear diffuser, cf rear wing, cf mirrors & bonnet scoop.....etc. Ha! Still stock for now. I do love the new JCW! :-)
Trending Topics
#8
That looks so sharp.
One issue that I noticed from the photos from japan and the local distributer is that the gap between the spoiler and the existing from fender skirt seems wider than stock and does not appear parallel like stock. Any chance you could comment on this and maybe show a close picture of this junction?
#12
I've voiced my opinion on this splitter before. It's a dirt trap basically.
I would consider this one. It is a true piece of design not an afterthought.
http://www.3ddesign.jp/english/produ...INI_F55_56.htm
Thoughts?
I would consider this one. It is a true piece of design not an afterthought.
http://www.3ddesign.jp/english/produ...INI_F55_56.htm
Thoughts?
#13
I must agree on the value for money. I can buy a set of nice aftermarket rims for less than the 3ddesign splitter. That being said..they must only make very few off these. I bet if they were for a Honda civic they would be way cheaper. Custom parts for a fairly rare car will always cost more than you would think...and this is way more complicated to make than an exhaust system.
#14
#16
#17
Facebook Post
Facebook Post
#18
Iam quite happy with the "Schnitzer-Sword". Besides that there is no 2nd material used, carbon or cfk, it fits 100 % to the OE look. Further it is TÜV approved, meaning i can add it legally to the car.
https://www.facebook.com/15676219067...type=3&theater
https://www.facebook.com/15676219067...type=3&theater
https://www.facebook.com/15676219067...type=3&theater
https://www.facebook.com/15676219067...type=3&theater
Last edited by 02fanatic; 05-14-2016 at 08:45 AM. Reason: Updated after viewing on computer screen
#19
I believe that Andreas Hartmann at AC Schnitzer USA has a splitter in stock. Meaning the total cost is $400. If you speak nicely it will not cost much to ship. I've thought long and hard and have decided that this is the way to go. Although the 3DDesign is superior looking - being CF makes it completely impractical as it is impossible to repair. I can live with the JCW Pro Splitters and the Schnitzer combo. I am going to have to epoxy in the PDC sensor into the Pro splitters ....somehow!
#20
I believe that Andreas Hartmann at AC Schnitzer USA has a splitter in stock. Meaning the total cost is $400. If you speak nicely it will not cost much to ship. I've thought long and hard and have decided that this is the way to go. Although the 3DDesign is superior looking - being CF makes it completely impractical as it is impossible to repair. I can live with the JCW Pro Splitters and the Schnitzer combo. I am going to have to epoxy in the PDC sensor into the Pro splitters ....somehow!
#21
I believe that Andreas Hartmann at AC Schnitzer USA has a splitter in stock. Meaning the total cost is $400. If you speak nicely it will not cost much to ship. I've thought long and hard and have decided that this is the way to go. Although the 3DDesign is superior looking - being CF makes it completely impractical as it is impossible to repair. I can live with the JCW Pro Splitters and the Schnitzer combo. I am going to have to epoxy in the PDC sensor into the Pro splitters ....somehow!
#22
#23
#24
We carry AC Schnitzer for MINI now !
Here is the front splitter: They have one for the NON JCW Aero kit :
https://www.ecstuning.com/Search/SiteSearch/5111256150/
And One for the JCW Aero kit front bumper 5111256160
https://www.ecstuning.com/Search/SiteSearch/5111256160/
Here is the front splitter: They have one for the NON JCW Aero kit :
https://www.ecstuning.com/Search/SiteSearch/5111256150/
And One for the JCW Aero kit front bumper 5111256160
https://www.ecstuning.com/Search/SiteSearch/5111256160/
__________________
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
Last edited by ECSTuning; 09-25-2018 at 12:01 PM.