Hope this is the right place to post...

Just thought I'd share photos of my clear bra install sent to me from the installer, Vincent, over at Omega Tintwerks (925.227.1322 in Pleasanton, CA if you're in the area). I thought he did a fantastic job. It was custom done, but I can hardly tell.

I did the whole hood (instead of half) because I decided I can't stand the line that shows up where it would have ended. And I guess I had money to burn. Ha.

There are some closeups of where the seaming ends. I can't tell on my car unless I actually feel for it.

 

Just a couple more...

 

wow, that must have cost a lot of money.

it looks very well done though. especially sicne it apperas the material was tucked behind edges.

 

Awesome stuff. I'm getting mine installed here in a couple of days.

 

Nice!

 

Looks great! What was the damage ($$$) on the full hood install?

 

Looks good!
I've heard nothing but positive comments about Vincent, I'd be interested in knowing the final bill as well, I believe I'll probably see him right after I get my mini (he's just down the street from EB Mini).

 

Top notch install. Looks much nicer than the pre-cut films.

 

hey i looked up his omegas number and it was disconnected when i called, do u have a number where he can be reached at?

 

hi guys, thanks for posting the pixs girlcavity. im the owner and installer of Omega Tintwerks. i ve been getting a lot of inquiries concerning this thread. i thought i check in. i 've done many standard Minis pre-cut kits. this is the first full wrap hood i ve done for the mini. the PPF brand is call VentureShield. it is virtually invisible. it does nt have the 'orange peel effect' like the 3M brand(5 yrs Warranty). VentureShield in the clearest in the industry and comes w/ a lifetime warranty. if you like more info or club forum deals give us a call.

-vincent
925.227.1322
since 1989

ps. yes were are block from Pleasanton Auto Mall and East Bay Mini

 

LOL Vincent are you on every motoring forum? I picked up your name from several different forums including the Corvette one, a subaru forum, and several others.

I do have a question, maybe you or someone can answer. If you put an clear bra alternative on a vehicle how do you keep it clean? Is it just like a clear coat? I've seen some nasty spots on cars where some evil bird has taken a carp on the car. Can I treat the VentureShield like paint? Does it work ok with powered orbital polishers like porter cable? Was wondering if it might melt the material.

Thanks!

 

Is it possible to set up a group buy? Call the norcal minis phone when you have time. 510-881-3456

 

if there is a group buy, id be in 100%!!!!!

 

Hey all,

kreative sent me a pm with some questions so I'll answer them here...

- What type of film did he use? (3M, Ventureshield, other?)
Ventureshield

- Any warranty on the clear bra job?
I believe Ventureshield offers lifetime warranty.

- How long did the install take?
I'm guessing 4-5 hours.

- Does he also tint windows?
Yes I plan to tint mine from him in a few months.

Also, the difference between whole hood and half hood was quoted to me as $250.

 

i'd definitely be interested in a group buy

thanks girlcavity for your reply!

 

Yes, thanks for the reply, $250 .. that's not bad. Did he mention care for the Ventureshield? Does it act like a clear coat? Can it be buffed using an electric polisher? :-) I'd be interested in doing the full hood too if I can keep it looking good.

Thanks!

 

He told me to treat it normally -- it can be washed, waxed, etc. I don't know to what extent though. I bet some forum/web search will give you better info.

Bird poo is really bad for it if left to sit on the clear bra and possibly with sun. I was under the impression that there was only stain danger within the first week or so of install, but I'm not sure...

 

vince tinted my car on monday! and its awesome! i got 35% all around! he beveled the edges so it flows and looks like there isnt a tint line! i recommend him for the tint! and im going to clear bra my car soon by vince!

thnx vince for the tint!

 

anyone talk to vince about a group buy yet?

 

+1! I want a clear bra!

 

huuum I need one of those looks really nicely done. Which I could find someone locally to do it that is at that level... rocks/pebbels are starting to get me.

 

For the MINI?! That makes sense now

 

Yup, im a *****...ppl pass me around when they are happy w/ my work. plus reasonable prices, ppl tend to share their experience

 

Do not treat the clear bra like paint or use a orbital polisher. The high speed buffer will burn it. I recommend you wash/dry it and spray on a clear quick detail wax w/ a microfiber. Once a month that will keep the road bugs and bird crap from staining the bra.

 

check your PM