Bimmercode App
#1
Bimmercode App
TVPostSound listed some expert coding that I saved for a cheatsheet. I add to it as I find new coding procedures. This is what I have saved so far.
Bimmercode Expert Mode:
Add as you wish, but only tested and working functions.
NON UJ Brake Force Display BLINKING
https://www.northamericanmotoring.co...-blinking.html
Activate Rear Fog Lights:
3068 NSL_Verbaut = Verbaut
Code first, then cycle ignition, then restart Bimmercode for the below options
to show up
Activate Rear Fog Lights feature for lighting switch:
3064 Mapping_Nebelschlussl_L_output = nsl_l
3064 Mapping_Nebelschlussl_L_Function = nebelschlusslicht
3064 Mapping_Nebelschlussl_R_output = nsl_r
3064 Mapping_Nebelschlussl_R_Function = Nebelschlusslicht
Close windows, sunroof & mirror from key fob:
3056 KOMFORTSCHLIESSUNG_FB = aktiv 00
Turn off window roll-up door interrupt when ignition off, and door is being opened:
3050 FH_TUERAUF_STOP_MAUT =aktiv
Disable Active Sound Design
3000 ASD_SOUND_OFF = aktiv
Display Tire Pressure & Temperature in Vehicle Info:
3001 RDC_SAFETY = aktiv
enabling foglights with high beams.
BDC Module
3068 NSW_AUS_BEI_FL nicht aktiv
It translates to fog lights OFF with high beams (default is aktiv)
So you double negative the response to leave on.
Enable Illumination of Exterior Door Handle LEDs when in Reverse
3070 OVT_BEI_REUCKFAHRLICHT =aktiv
Change momentary turn signal to 5 blinks. - Unconfirmed if this works
3069
PIA_DEFAULT_TIPPBLINKEN =FUENFMAL
Enable JCW Tach in HUD (I found this on another site, so if you try it and it doesn't work let me know)
HU_NBT > EXPERT MODE > HUD_SPORTANZEIGE_ENABLE, HUD_SPORTANZEIGE_FES_ENABLE, and HUD_SPORTANZEIGE_MS_GASSE_ENABLE to AKTIV.
Code
Then
KOMBI > EXPERT MODE > FZG_Aussttang,HUD _SPORTANZEIGE_ENABLE, HUD_SPORTANZEIGE_FES_ENABLE, and HUD_SPORTANZEIGE_MS_GASSE_ENABLE to AKTIV.
Code
Rear Fogs as Brake Lights: (This hasn't been checked on a car w/rear fogs working)
BDC_BODY
3065 LceLampMapping4, ED
Funktionen
MAPPING_BREMSL_2_L_OUTPUT
Switch to this
nsl_l (this is the rear fog light choice)
You need to do this for right and left. Above is for left,
For RHS just change the l to r
MAPPING_BREMSL_2_R_OUTPUT
nsl_r__________________
When adding new Union Jack tail lights to earlier Gen 3 cars...
Coded the indicators in the basic mode - to not monitor and set to LED.
Then, Stephan from Bimmercode gave me the following to do in expert mode:
BL_R_IS_LED => aktiv
BL_R_WARMUEBERWACHUNG => nicht_aktiv
BL_R_KALTUEBERWACHUNG => nicht_aktiv
BL_L_IS_LED => aktiv
BL_L_WARMUEBERWACHUNG => nicht_aktiv
BL_L_KALTUEBERWACHUN => nicht_aktiv
Bimmercode Expert Mode:
Add as you wish, but only tested and working functions.
NON UJ Brake Force Display BLINKING
https://www.northamericanmotoring.co...-blinking.html
Activate Rear Fog Lights:
3068 NSL_Verbaut = Verbaut
Code first, then cycle ignition, then restart Bimmercode for the below options
to show up
Activate Rear Fog Lights feature for lighting switch:
3064 Mapping_Nebelschlussl_L_output = nsl_l
3064 Mapping_Nebelschlussl_L_Function = nebelschlusslicht
3064 Mapping_Nebelschlussl_R_output = nsl_r
3064 Mapping_Nebelschlussl_R_Function = Nebelschlusslicht
Close windows, sunroof & mirror from key fob:
3056 KOMFORTSCHLIESSUNG_FB = aktiv 00
Turn off window roll-up door interrupt when ignition off, and door is being opened:
3050 FH_TUERAUF_STOP_MAUT =aktiv
Disable Active Sound Design
3000 ASD_SOUND_OFF = aktiv
Display Tire Pressure & Temperature in Vehicle Info:
3001 RDC_SAFETY = aktiv
enabling foglights with high beams.
BDC Module
3068 NSW_AUS_BEI_FL nicht aktiv
It translates to fog lights OFF with high beams (default is aktiv)
So you double negative the response to leave on.
Enable Illumination of Exterior Door Handle LEDs when in Reverse
3070 OVT_BEI_REUCKFAHRLICHT =aktiv
Change momentary turn signal to 5 blinks. - Unconfirmed if this works
3069
PIA_DEFAULT_TIPPBLINKEN =FUENFMAL
Enable JCW Tach in HUD (I found this on another site, so if you try it and it doesn't work let me know)
HU_NBT > EXPERT MODE > HUD_SPORTANZEIGE_ENABLE, HUD_SPORTANZEIGE_FES_ENABLE, and HUD_SPORTANZEIGE_MS_GASSE_ENABLE to AKTIV.
Code
Then
KOMBI > EXPERT MODE > FZG_Aussttang,HUD _SPORTANZEIGE_ENABLE, HUD_SPORTANZEIGE_FES_ENABLE, and HUD_SPORTANZEIGE_MS_GASSE_ENABLE to AKTIV.
Code
Rear Fogs as Brake Lights: (This hasn't been checked on a car w/rear fogs working)
BDC_BODY
3065 LceLampMapping4, ED
Funktionen
MAPPING_BREMSL_2_L_OUTPUT
Switch to this
nsl_l (this is the rear fog light choice)
You need to do this for right and left. Above is for left,
For RHS just change the l to r
MAPPING_BREMSL_2_R_OUTPUT
nsl_r__________________
When adding new Union Jack tail lights to earlier Gen 3 cars...
Coded the indicators in the basic mode - to not monitor and set to LED.
Then, Stephan from Bimmercode gave me the following to do in expert mode:
BL_R_IS_LED => aktiv
BL_R_WARMUEBERWACHUNG => nicht_aktiv
BL_R_KALTUEBERWACHUNG => nicht_aktiv
BL_L_IS_LED => aktiv
BL_L_WARMUEBERWACHUNG => nicht_aktiv
BL_L_KALTUEBERWACHUN => nicht_aktiv
Last edited by Mini_Vinnie; 05-14-2018 at 05:55 AM.
#2
Thanks for starting a new one!!
There are some that still don't understand how Bimmercode works.
Yes, there are pretty little switch graphics to change options, but they are limited, and do not always work. These are shortcuts, or macros, the author has chosen to give you. He tries to update that as best he can.
The basis for this app is buried in EXPERT MODE.
Expert mode is EVERYTHING that can be done to your MINI.
The app reads your modules, and lists ALL functions.
You need to understand German, as that is what the modules spit out GERMAN!!
I personally don't like the shortcuts, I like EXPERT MODE, as I have full control.
Thats why, I listed expert mode settings.
Thank you
There are some that still don't understand how Bimmercode works.
Yes, there are pretty little switch graphics to change options, but they are limited, and do not always work. These are shortcuts, or macros, the author has chosen to give you. He tries to update that as best he can.
The basis for this app is buried in EXPERT MODE.
Expert mode is EVERYTHING that can be done to your MINI.
The app reads your modules, and lists ALL functions.
You need to understand German, as that is what the modules spit out GERMAN!!
I personally don't like the shortcuts, I like EXPERT MODE, as I have full control.
Thats why, I listed expert mode settings.
Thank you
#4
The following 4 users liked this post by Mini_Vinnie:
#5
#6
Just adding another data point on the addition of rear fogs as brake lights -- a few moments ago I successfully coded the function without issues on my '17 Clubman S All4. The update was made using a vGate Wifi iCar2 Elm327 OBD adapter and the bimmercode app running on an iPad.
The car is not factory-equipped to operate the rear fogs, and thus lacks a dashboard switch. I "activated" the rear fogs in a coding first-step, and then coded their use as rear brake lights, per the steps offered by Mini_Vinnie (and now included in the main thread entry above). All went fine, no error codes or other issues.
For the F54, I think this is a big deal. The low-mounted bumper brake lights are less than confidence-inspiring when you've got a truck tailgating on the expressway (all too common here, unfortunately).
On another forum, someone from the UK who made the same update, and whose car _is_ factory-equipped with the rear fogs dashboard switch, indicated that when the switch is activated, the fogs are steady "on," and when the switch is off, the fogs then function as brake lights. So at least the controller seems smart enough to differentiate. I won't be able to confirm unless/until I get the dashboard switch.
Anyway -- thanks, very happy!
The car is not factory-equipped to operate the rear fogs, and thus lacks a dashboard switch. I "activated" the rear fogs in a coding first-step, and then coded their use as rear brake lights, per the steps offered by Mini_Vinnie (and now included in the main thread entry above). All went fine, no error codes or other issues.
For the F54, I think this is a big deal. The low-mounted bumper brake lights are less than confidence-inspiring when you've got a truck tailgating on the expressway (all too common here, unfortunately).
On another forum, someone from the UK who made the same update, and whose car _is_ factory-equipped with the rear fogs dashboard switch, indicated that when the switch is activated, the fogs are steady "on," and when the switch is off, the fogs then function as brake lights. So at least the controller seems smart enough to differentiate. I won't be able to confirm unless/until I get the dashboard switch.
Anyway -- thanks, very happy!
The following 4 users liked this post by 1200K:
#7
Trending Topics
#8
Join Date: Aug 2016
Location: California Native still livin' in LaLa Land
Posts: 2,162
Received 507 Likes
on
383 Posts
There's this:
https://www.northamericanmotoring.co...ke-lights.html
#9
handn has done it. I think with ESYS.
There's this:
https://www.northamericanmotoring.co...ke-lights.html
There's this:
https://www.northamericanmotoring.co...ke-lights.html
Minnie, the F54’s fog lights are in the rear doors, between the tail lights and the reverse lights. Nicely higher than the bumper lenses. There’s a photo in the thread at minif56.com.
#10
#11
#13
#14
Hmm - I'm trying to get rear fogs to work as brake lights in my F56 (I have the bulbs but not the switch)
Are these only three things I need to change?
* 3065 LceLampMapping4 MAPPING_BREMSL_2_L_OUTPUT
* 3065 LceLampMapping4 MAPPING_BREMSL_2_R_OUTPUT
* 3068 NSL_Verbaut
Because I changed these three things and the fogs still aren't lighting with the brakes. Any advice would be appreciated.
Are these only three things I need to change?
* 3065 LceLampMapping4 MAPPING_BREMSL_2_L_OUTPUT
* 3065 LceLampMapping4 MAPPING_BREMSL_2_R_OUTPUT
* 3068 NSL_Verbaut
Because I changed these three things and the fogs still aren't lighting with the brakes. Any advice would be appreciated.
Last edited by punkgeek; 12-25-2017 at 01:42 PM. Reason: better english
#15
#16
#17
#18
#19
Coded Display Tire Pressure & temp, works !
Coded Hu NBT Enable Video, works, not sure why we need this.
Coded Import routes into Navi_trip_import but don't have any idea how this works yet. Will leave it to wife to figure out if it does anything.
Couldn't find Speech_2_text , not sure if it is available on this car.
#20
I just downloaded the Bimmer app. Connected and having a look around, I would like to try this code out . Where do l look for the first part of coding?
Activate Rear Fog Lights:
3068 NSL_Verbaut = Verbaut
Code first, then cycle ignition, then restart Bimmercode for the below options
to show up
Activate Rear Fog Lights feature for lighting switch:
3064 Mapping_Nebelschlussl_L_output = nsl_l
3064 Mapping_Nebelschlussl_L_Function = nebelschlusslicht
3064 Mapping_Nebelschlussl_R_output = nsl_r
3064 Mapping_Nebelschlussl_R_Function = Nebelschlusslicht
Is in under BDC_body? Sorry Im a newbie.
Thanks
Activate Rear Fog Lights:
3068 NSL_Verbaut = Verbaut
Code first, then cycle ignition, then restart Bimmercode for the below options
to show up
Activate Rear Fog Lights feature for lighting switch:
3064 Mapping_Nebelschlussl_L_output = nsl_l
3064 Mapping_Nebelschlussl_L_Function = nebelschlusslicht
3064 Mapping_Nebelschlussl_R_output = nsl_r
3064 Mapping_Nebelschlussl_R_Function = Nebelschlusslicht
Is in under BDC_body? Sorry Im a newbie.
Thanks
#21
I just downloaded the Bimmer app. Connected and having a look around, I would like to try this code out . Where do l look for the first part of coding?
Activate Rear Fog Lights:
3068 NSL_Verbaut = Verbaut
Code first, then cycle ignition, then restart Bimmercode for the below options
to show up
Activate Rear Fog Lights feature for lighting switch:
3064 Mapping_Nebelschlussl_L_output = nsl_l
3064 Mapping_Nebelschlussl_L_Function = nebelschlusslicht
3064 Mapping_Nebelschlussl_R_output = nsl_r
3064 Mapping_Nebelschlussl_R_Function = Nebelschlusslicht
Is in under BDC_body? Sorry Im a newbie.
Thanks
Activate Rear Fog Lights:
3068 NSL_Verbaut = Verbaut
Code first, then cycle ignition, then restart Bimmercode for the below options
to show up
Activate Rear Fog Lights feature for lighting switch:
3064 Mapping_Nebelschlussl_L_output = nsl_l
3064 Mapping_Nebelschlussl_L_Function = nebelschlusslicht
3064 Mapping_Nebelschlussl_R_output = nsl_r
3064 Mapping_Nebelschlussl_R_Function = Nebelschlusslicht
Is in under BDC_body? Sorry Im a newbie.
Thanks
Remember, if you dont have a toggle switch to activate the rear fogs then it is a pointless thing to code because it wont do anything
#24
#25
Rear Fogs as Brake Lights:
BDC_BODY
3065 LceLampMapping4, ED
Funktionen
MAPPING_BREMSL_2_L_OUTPUT
Switch to this
nsl_l (this is the rear fog light choice)
You need to do this for right and left. Above is for left,
For RHS just change the l to r
MAPPING_BREMSL_2_R_OUTPUT
nsl_r__________________
The following users liked this post:
GooGoomuc (01-04-2018)