JCW What and where do I get gaskets ?
#1
What and where do I get gaskets ?
So this manifold I got cane with the thermal barrier spacers and it also has NO groves for o ring gaskets.
so here's my questions :
do I need 2x gaskets for the tbody and for the cylinder head to intake ? So do I need to put a gasket on each side if the thermal barriers ?? I'd assume so but....
AND where would I find a gaskets that would match ??? Or do I need to cut and make my own with a gasket sheet ? If so , what type material gaskets do you suggest ??.
so here's my questions :
do I need 2x gaskets for the tbody and for the cylinder head to intake ? So do I need to put a gasket on each side if the thermal barriers ?? I'd assume so but....
AND where would I find a gaskets that would match ??? Or do I need to cut and make my own with a gasket sheet ? If so , what type material gaskets do you suggest ??.
#2
#3
though heck , it's worth a try... thx you.
But I think I'm gonna buy gasket material just to have on hand just encase..
Also , is it safe for me to block off/delete passengers side pcv ? , id like a cleaner , better running ,flowing intake setup and I can have cel codes deleted out via adriancl. I found the block off cap for the valve cover but i dont wanna risk excessive crankcase pressure from building up.
other than the pcv I'd like to run all the other vacuum stuff as much as stock as possible.
BUT I will go to hardware store today and see if I can find a attachment that'd allow me to plumb in the pcv but i think that's gonna be luck if I do so I have mone of that so I need to plan and have backup plans then too.
#4
I actually got email back already from speedtech " it came with 2x gaskets , they are white and in a separate box. Please make sure they were included and didn't accidentally throw them away "
Are these phenolic spacers not spacers but actually thermal gaskets ? i cant imagine so but i tend to be wrong alot lately..
Are these phenolic spacers not spacers but actually thermal gaskets ? i cant imagine so but i tend to be wrong alot lately..
Last edited by MiniManAdam; 04-06-2024 at 06:38 AM.
#5
Speedtech WAS rite...
I guess I just use the plastic things as the gaskets.
from what I found out : they are actually thermal gaskets which is same as a phenolic spacer. The thermal gaskets SHOULD seal without any other gaskets or rtv ect. They ARE also reusable which is a plus.
sooooo , when I install them , just to be safe because I'm **** , I WILL use copper gasket spray on both sides of the thermal gasket juuuuuuust to be safe. Back with my r53's i religiously used copper spray on the header gasket , intake manifold gasket and the supercharger horn gaskets. And never once did I EVER get a leak. I also do a good job prepping the surfaces too..
so wish me luck on the install guys !!! I will make a thread about my opinions on this manifold too.
I guess I just use the plastic things as the gaskets.
from what I found out : they are actually thermal gaskets which is same as a phenolic spacer. The thermal gaskets SHOULD seal without any other gaskets or rtv ect. They ARE also reusable which is a plus.
sooooo , when I install them , just to be safe because I'm **** , I WILL use copper gasket spray on both sides of the thermal gasket juuuuuuust to be safe. Back with my r53's i religiously used copper spray on the header gasket , intake manifold gasket and the supercharger horn gaskets. And never once did I EVER get a leak. I also do a good job prepping the surfaces too..
so wish me luck on the install guys !!! I will make a thread about my opinions on this manifold too.
Thread
Thread Starter
Forum
Replies
Last Post
Oh Six Mini
R50/R53 :: Hatch Talk (2002-2006)
6
09-04-2019 05:53 AM