F60 What did you do to/with your CM today?
#151
The following 3 users liked this post by BootMKR:
#152
Tinted.
De-badged front without realizing it had guide holes so replaced with all black. Rear CM gone.
Have black handles, mud flaps not installed yet.
New Rims and tires not installed yet.
H&R lowering springs not installed yet.
Cold Air Induction installing tomorrow.
Elite tune next.
Black trims next also.
De-badged front without realizing it had guide holes so replaced with all black. Rear CM gone.
Have black handles, mud flaps not installed yet.
New Rims and tires not installed yet.
H&R lowering springs not installed yet.
Cold Air Induction installing tomorrow.
Elite tune next.
Black trims next also.
#154
The following users liked this post:
Brainygadgetgirl (12-08-2019)
#157
would be great.
I live in peru and I must buy abroad.
looking for door handle covers, mudguards and headlight and taillight black bezel oh, and piano black or CF overlays for the steering wheel “arms”
seen some on aliexpress but don’t know if the products quality.
I live in peru and I must buy abroad.
looking for door handle covers, mudguards and headlight and taillight black bezel oh, and piano black or CF overlays for the steering wheel “arms”
seen some on aliexpress but don’t know if the products quality.
#160
The following 3 users liked this post by cuppajoe:
#161
#162
Got a new to me 2018 All4 S in Midnight Black metallic so I am just trying to make it "mine". Got new weathertechs all around, K&N air filter, got a parcel shelf from a forum member. Did some minor coding with Bimmercode and Bimmerlink. This is my 4th MINI and so far very enjoyable. Picked up a buddy of mine for dinner last night who normally drives a corvette and XKE and he was impressed with the seats and how much room there was.
Al
Al
#163
Got a new to me 2018 All4 S in Midnight Black metallic so I am just trying to make it "mine". Got new weathertechs all around, K&N air filter, got a parcel shelf from a forum member. Did some minor coding with Bimmercode and Bimmerlink. This is my 4th MINI and so far very enjoyable. Picked up a buddy of mine for dinner last night who normally drives a corvette and XKE and he was impressed with the seats and how much room there was.
Al
Al
#167
Installed new wheels.
Wheels
ESR AP6
19x8.5, 5x112 (customs drilled), +30, 72.6 center bore
Rotary forged / flow formed
21lbs
Tires
Hankook Ventus2 Concept2
245/40/19
The wheels needed 5mm spacers to clear the JCW calipers. Those required some M14x1.25 33mm lug bolts. I was hoping to get some red lug bolts, but couldn’t find them at that size.
Also since the center bore is 72.6mm I got some hub centric adapters on Amazon.
Wheels
ESR AP6
19x8.5, 5x112 (customs drilled), +30, 72.6 center bore
Rotary forged / flow formed
21lbs
Tires
Hankook Ventus2 Concept2
245/40/19
The wheels needed 5mm spacers to clear the JCW calipers. Those required some M14x1.25 33mm lug bolts. I was hoping to get some red lug bolts, but couldn’t find them at that size.
Also since the center bore is 72.6mm I got some hub centric adapters on Amazon.
The following users liked this post:
miniRogue1 (04-29-2023)
#169
@cuppajoe looking good. And is that all you need to fit around the big jcw brakes…spacers or are there only certain wheels too
Also, I did ceramic coat these to make them easier to clean.
The following users liked this post:
miniRogue1 (04-29-2023)
Thread
Thread Starter
Forum
Replies
Last Post
MaybeMCSC
General MINI Talk
4
07-09-2011 03:31 PM