Interior/Exterior Polishing R90 project
#27
Lots of places supply parts for multi-piece BBS bolts. I got my gold plated bolts from RK importing.
www.justmatz.co.uk has some different choices...
And if these guys can't get you what you need....you're probably out of luck http://www.titanium-touch.de/titaniu...h_index_uk.htm
#29
I called BBS, he said 21 ft/lbs for torque on most of their wheels, but they don't sell the stock bolts anymore for liability reasons I guess. So I guess i'm going aftermarket for the bolts!
Rally, can I ask you how much you spent on brand new bolts? I might get a nice new set enough for all 4 wheels to spruce them up a little as well. How long did it take you to get them in the mail?
Rally, can I ask you how much you spent on brand new bolts? I might get a nice new set enough for all 4 wheels to spruce them up a little as well. How long did it take you to get them in the mail?
Last edited by ColinMc; 03-12-2008 at 10:57 AM.
#30
I got them from a company that had them in stock here in the US so it only took like a week to get them from CA. I don't think they carry r90 bolts so you will have to look around at the sites i listed.
And 21ft/lbs.....that's what i figured. That's a lot higher than the BBS RS specs. So the OP should probably retorque
Last edited by Rally@StanceDesign; 03-12-2008 at 11:56 AM.
#32
Those bolts are beauties.
I am thinking some dark blue bolts to accent the wheels when I find some...and having the wheels the factory Anthricite color. I found the Kodiak sheet and am deciding measurements.
What do you think about polished lips+dk blue bolts+anthricite centers?
What about lugs and center cap?
#37
#41
Hey guys, I recieved an email from www.titanium-touch.com They think that they have the bolts we need...M7x24.5 in Ti. I am going to double check it when I get my rims...but if any of you guys could measure the bolts that would speed it up...
Hope this helps us all
Hope this helps us all
#43
Nah...they are 2-piece in a different way than mine are. The r90's are setup so that the centers come out rather than the lips. In order to go wider you need a full new barrel/lip to put the center in.
#45
Theoretically, yes, but I don't think the R90 has ever been made for anything besides the MINI so I think it would be next to impossible to find barrel that the R90 just happens to fit in.
#47
Ok, so after my last email with ti touch. I will not be buying the bolts through them...nothing wrong with them by any means, just the exchange rate I knew our $ was in the toilet, but man I would have to pay $213.67 for just 60 bolts shipped(these are Ti plain finish) and it would be $590.18 shipped for color matched...
Now if I can use SS I may still go with them.
I have found their bolts on ebay on the de, nl, and other ebay branches and they are much less$$$
Rally if you have any sources or advise I would love it
Chris.
Now if I can use SS I may still go with them.
I have found their bolts on ebay on the de, nl, and other ebay branches and they are much less$$$
Rally if you have any sources or advise I would love it
Chris.
#48
Ok, so after my last email with ti touch. I will not be buying the bolts through them...nothing wrong with them by any means, just the exchange rate I knew our $ was in the toilet, but man I would have to pay $213.67 for just 60 bolts shipped(these are Ti plain finish) and it would be $590.18 shipped for color matched...
Now if I can use SS I may still go with them.
I have found their bolts on ebay on the de, nl, and other ebay branches and they are much less$$$
Rally if you have any sources or advise I would love it
Chris.
Now if I can use SS I may still go with them.
I have found their bolts on ebay on the de, nl, and other ebay branches and they are much less$$$
Rally if you have any sources or advise I would love it
Chris.
#49
Did some digging. Re-measured my bolts= M7x1.0x24mm 8mm triple square head (female). Not too un-common after all just not typical.
Found these here; http://yhst-1918367471896.stores.yah...bsrmbolts.html not the same but might work, head is an outie not innie.
Found these here; http://yhst-1918367471896.stores.yah...bsrmbolts.html not the same but might work, head is an outie not innie.