North American Motoring - Search Results

Go Back  North American Motoring > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: EdsNotHere
Showing results 1 to 50 of 129
Search took 0.01 seconds.
01-03-2019, 09:23 PM
Replies: 8
Views: 694
Posted By EdsNotHere

I jack up mine on left side first and put the...

I jack up mine on left side first and put the jackstands under the subframe front and rear then do the same on the right.
12-22-2018, 08:28 PM
Replies: 2
Views: 441
Posted By EdsNotHere

Yep it’s fairly normal. Scotchbright and clean...

Yep it’s fairly normal. Scotchbright and clean them up.
12-20-2018, 05:55 PM
Replies: 6
Views: 703
Posted By EdsNotHere

sold

Sold
12-19-2018, 09:10 PM
Replies: 6
Views: 703
Posted By EdsNotHere

All PM’s responded to.

All PM’s responded to.
12-15-2018, 10:41 PM
Replies: 6
Views: 703
Posted By EdsNotHere

12-15-2018, 10:06 PM
Replies: 6
Views: 482
Posted By EdsNotHere

No response is what happens when the latch fails....

No response is what happens when the latch fails. Mine did the same thing. Getting the right inner trim off is a 50/50 shot it doesn’t break. The left is a bear. The left one won’t activate till the...
12-15-2018, 10:03 PM
Replies: 3
Views: 416
Posted By EdsNotHere

Vote for the Schwaben also. I use mine all the...

Vote for the Schwaben also. I use mine all the time. Change idle speed, clear codes, check readings.
11-28-2018, 08:30 PM
Replies: 9
Views: 471
Posted By EdsNotHere

If you have a latch that’s not working I’d...

If you have a latch that’s not working I’d replace both latches to avoid it not opening and then it’s a PIA to get open when the latch fails. I replaced both of mine when the left one failed.
10-08-2018, 11:52 PM
Replies: 15
Views: 1,642
Posted By EdsNotHere

If they are still for sale I’m in Phoenix and...

If they are still for sale I’m in Phoenix and would be able to drive over and pick them up. Where in SoCal are you?
10-08-2018, 11:43 PM
Replies: 3
Views: 682
Posted By EdsNotHere

I just ordered the MT one from ECS and will be...

I just ordered the MT one from ECS and will be here Friday and I’ll post my thoughts after install.
Forum: Suspension
10-07-2018, 11:46 AM
Replies: 15
Views: 1,752
Posted By EdsNotHere

They were on amazon

They were on amazon
09-07-2018, 05:54 PM
Replies: 7
Views: 1,229
Posted By EdsNotHere

it does come with the sender but but not the...

it does come with the sender but but not the radiator hose adapter. The boost has a electric sender that the boost/vacuum tube would attach to.
09-04-2018, 09:48 PM
Replies: 6
Views: 628
Posted By EdsNotHere

I use the Delphi ones off Amazon and at 20lbs of...

I use the Delphi ones off Amazon and at 20lbs of boost not a single issue. Mine had Delphi OEM
09-04-2018, 04:58 PM
09-04-2018, 01:23 AM
Replies: 2
Views: 454
Posted By EdsNotHere

Mine the CD player cycles and makes a noise....

Mine the CD player cycles and makes a noise. Nothing from the fuse panel though.
08-31-2018, 08:05 PM
Replies: 5,479
Views: 1,719,453
Posted By EdsNotHere

Nice. Someone else with the Pace wheels. I’ve...

Nice. Someone else with the Pace wheels. I’ve only seen my mini here in Phoenix with them.
08-09-2018, 08:42 PM
Replies: 4
Views: 823
Posted By EdsNotHere

I have the Neuspeed on mine and sounds just...

I have the Neuspeed on mine and sounds just right. Nice a throaty but overly loud.
07-22-2018, 05:24 PM
Replies: 7
Views: 1,187
Posted By EdsNotHere

still working great. I did adjust the waste gate...

still working great. I did adjust the waste gate about a half trun less on the boost and to holds boost a bit less but no surging or issues. Lately it’s harder to tell since it’s been averaging 108°...
Forum: Electrical
07-22-2018, 10:39 AM
Replies: 9
Views: 1,313
Posted By EdsNotHere

Check this too. ...

Check this too.

https://www.northamericanmotoring.com/forums/r55-clubman-talk-2008/319213-09-r55-back-up-camera.html#post4377286
07-16-2018, 10:06 PM
Replies: 1
Views: 357
Posted By EdsNotHere

The bulb mounting board should be the same just...

The bulb mounting board should be the same just swap them and should work
07-15-2018, 10:52 AM
Replies: 6
Views: 896
Posted By EdsNotHere

I just have the stock turbo shield and removed...

I just have the stock turbo shield and removed the AEM shield due to potential issues with the valve cover melting. In AZ and 105°-110° temps and have had no issues with the intake duct melting.
07-15-2018, 10:40 AM
Replies: 2
Views: 347
Posted By EdsNotHere

No need to activate the ABS. Best way is to get a...

No need to activate the ABS. Best way is to get a pressure bleeder and it’s a quick easy no air in the line job.

I got this one and works perfect. ...
07-09-2018, 08:31 PM
07-07-2018, 09:31 PM
07-07-2018, 05:42 PM
Replies: 5
Views: 436
Posted By EdsNotHere

Mine tops out at 22psi and in AZ want to make...

Mine tops out at 22psi and in AZ want to make sure I’m running cool. Pm sent
07-07-2018, 05:21 PM
Replies: 5
Views: 436
Posted By EdsNotHere

How accurate are the boost readings? I’m...

How accurate are the boost readings? I’m interested
07-02-2018, 09:15 PM
Replies: 15
Views: 1,983
Posted By EdsNotHere

From the photos looks like they have been...

From the photos looks like they have been refinished before. The chips look rather deep and can see two different colors of paint. Is tha a large chunk ut the aluminum missing? D love to get these...
07-02-2018, 08:48 PM
Replies: 8
Views: 858
Posted By EdsNotHere

The mini do more hitch looks just like the Curt...

The mini do more hitch looks just like the Curt hidden hitch from Amazon for half the price
https://www.amazon.com/gp/product/B00IIURV9C/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
07-02-2018, 08:12 PM
Replies: 1
Views: 265
Posted By EdsNotHere

Ok found. And fixed. Turned out the be creaking...

Ok found. And fixed. Turned out the be creaking from right side of the steering rack. The noise was inside the boot sounds like a bushing was dry. Fixed by putting a small pinhole in the boot at the...
07-01-2018, 07:43 PM
Replies: 1
Views: 265
Posted By EdsNotHere

09 R55 Steering noise

About a couple weeks ago the clubby started making a squeaking / creaking noise when turning lightly an a standstill or moving slow. It sounds like it’s in the rack itself. I checked the upper...
06-26-2018, 11:02 PM
Replies: 5
Views: 656
Posted By EdsNotHere

It showed $37 on Real OEM

It showed $37 on Real OEM
06-21-2018, 09:32 PM
Replies: 5
Views: 656
Posted By EdsNotHere

It’s part of the molding. ...

It’s part of the molding.

http://www.realoem.com/bmw/enUS/part?id=MM33-USA-05-2009-R55-Mini-Cooper_S&mg=51&sg=20&diagId=51_6697&q=51372754070
06-19-2018, 09:22 PM
Replies: 8
Views: 858
Posted By EdsNotHere

https://www.etrailer.com/hitch-2009_mini_Clubman.h...

https://www.etrailer.com/hitch-2009_mini_Clubman.htm
06-19-2018, 09:03 PM
Replies: 8
Views: 858
Posted By EdsNotHere

https://cimg2.ibsrv.net/gimg/www.northamericanmoto...

https://cimg2.ibsrv.net/gimg/www.northamericanmotoring.com-vbulletin/2000x1504/80-289dbbf8_7b9b_4ad9_ad34_894419aa1229_53864285dd8ccc65cf61b5f7447ac0b8b85e3277.jpeg
I have the JCW aero kit on mine...
06-11-2018, 10:57 PM
Replies: 10
Views: 1,015
Posted By EdsNotHere

I’d love these. What would you sell the wheels...

I’d love these. What would you sell the wheels only shipped to 85296 AZ?
06-04-2018, 09:57 PM
Replies: 2
Views: 500
Posted By EdsNotHere

I was able to install a group 48 (H6) with no...

I was able to install a group 48 (H6) with no issue.
05-28-2018, 12:50 PM
Replies: 5
Views: 534
Posted By EdsNotHere

It’s serves to keep the dirt and debris out of...

It’s serves to keep the dirt and debris out of the heater plenum that’s below the right cowl. I suppose you could cut it but not sure if it would look ok or keep additional water and dirt out.
05-28-2018, 10:38 AM
Replies: 5
Views: 534
Posted By EdsNotHere

It’s part of the plastic cowl left and right it’s...

It’s part of the plastic cowl left and right it’s a few screws and clips and pull the wipers.
05-24-2018, 09:41 PM
Replies: 5
Views: 356
Posted By EdsNotHere

Doesn’t sound like a diverter valve. I had the...

Doesn’t sound like a diverter valve. I had the same issue and adjusted the waste gate to drop the boost below 21 lbs and problem solved. I have a manic stage 1
Forum: Electrical
05-16-2018, 02:46 PM
Replies: 4
Views: 616
Posted By EdsNotHere

They had to recalibrate the windows.

They had to recalibrate the windows.
05-13-2018, 09:28 PM
Replies: 5,479
Views: 1,719,453
Posted By EdsNotHere

Nice. I’m debating on a roof rack myself.

Nice. I’m debating on a roof rack myself.
05-13-2018, 09:21 PM
Replies: 23
Views: 1,325
Posted By EdsNotHere

The eraser wheel works better if the stripes are...

The eraser wheel works better if the stripes are in one piece. Once you remove the stripe and are left with the adhesive it doesn’t work well and you can burn through the paint quite easily. I would...
05-13-2018, 05:00 PM
Replies: 23
Views: 1,325
Posted By EdsNotHere

Go to an automotive paint supply store and get...

Go to an automotive paint supply store and get adhesive cleaner. It’s designed for just that. Anything else not so much and can possibly damage the paint I worked in body shops for 30 years and have...
05-08-2018, 08:26 PM
Replies: 7
Views: 1,187
Posted By EdsNotHere

I just st installed my GFB DV+ today and can say...

I just st installed my GFB DV+ today and can say you don’t get any more noise but you do get boost that holds for a bit longer and I’m running 22lbs of boost and I don’t get any blowoff at light...
05-08-2018, 08:18 PM
Replies: 0
Views: 561
Posted By EdsNotHere

Phoenix Mini.

Saw this cruising down the freeway today. ...
Forum: Electrical
05-07-2018, 09:25 PM
Replies: 4
Views: 616
Posted By EdsNotHere

I had the same problem. Had to go to dealer to...

I had the same problem. Had to go to dealer to have reset. No way around it. Cost me a 1/2 hour labor charge $75 at Mini of Tempe. Has worked perfect since.
05-05-2018, 11:19 PM
Replies: 4
Views: 626
Posted By EdsNotHere

I prefer NGK I’ve been using them for 40 + years...

I prefer NGK I’ve been using them for 40 + years and not a problem. I'm running 22 lbs of boost on my car and they never fail.
05-05-2018, 08:22 PM
Replies: 8
Views: 947
Posted By EdsNotHere

His car is a 2008 gen 2. Gen 1 had the headlight...

His car is a 2008 gen 2. Gen 1 had the headlight mounted in the hood. 2008-2012 should fit as everything else is the same. Fenders, latches, headlamps, and hinges all have the same part numbers...
05-05-2018, 09:03 AM
Replies: 5,479
Views: 1,719,453
Posted By EdsNotHere

Sgt. Pepper ...

Sgt. Pepper


https://cimg9.ibsrv.net/gimg/www.northamericanmotoring.com-vbulletin/2000x1709/80-823f8a83_9e3e_47a6_a4d8_e6f43e4cd5dc_16de4e6dc4f97f7aea1a147816e5f1e2f2f3ede3.jpeg
...
05-05-2018, 08:22 AM
Replies: 19
Views: 963
Posted By EdsNotHere

I guess if you were creative you could take the...

I guess if you were creative you could take the mesh rollers out and replace the fabric with a solid one. I thought about it but even in Phoenix the darkest limo tint was fine for me.
Showing results 1 to 50 of 129
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.