How to reset Adaptations?
#1
How to reset Adaptations?
2009 Cooper S with the Aisin 6-spd auto developed a bad shift flare from 3rd to 4th. Long story short: changed entire tranny and everything was fine, until I spun tires on wet pavement with DSC off. Now the problem is back. Shifts perfect in all other gears but 4th. Downshifts fine too. Just the pause between 3 and 4 is too long and RPMs shoot way up, then when it engages, jerks the car. That plays hell on the clutches, so it needs to be fixed ASAP.
I believe I just need to reset the transmission adaptations, but I can't find a tool to do it. Tried the $200 Autel scan tool and the $500 Foxwell Automaster with 0 success. No adaptation options. What do I need to reset them that doesn't cost $1000?
I believe I just need to reset the transmission adaptations, but I can't find a tool to do it. Tried the $200 Autel scan tool and the $500 Foxwell Automaster with 0 success. No adaptation options. What do I need to reset them that doesn't cost $1000?
The following 2 users liked this post by WayMotorWorks:
IDoSeaDoo (07-30-2018),
Rich Firth (03-24-2019)
#3
Mini CVT fix
2009 Cooper S with the Aisin 6-spd auto developed a bad shift flare from 3rd to 4th. Long story short: changed entire tranny and everything was fine, until I spun tires on wet pavement with DSC off. Now the problem is back. Shifts perfect in all other gears but 4th. Downshifts fine too. Just the pause between 3 and 4 is too long and RPMs shoot way up, then when it engages, jerks the car. That plays hell on the clutches, so it needs to be fixed ASAP.
I believe I just need to reset the transmission adaptations, but I can't find a tool to do it. Tried the $200 Autel scan tool and the $500 Foxwell Automaster with 0 success. No adaptation options. What do I need to reset them that doesn't cost $1000?
I believe I just need to reset the transmission adaptations, but I can't find a tool to do it. Tried the $200 Autel scan tool and the $500 Foxwell Automaster with 0 success. No adaptation options. What do I need to reset them that doesn't cost $1000?
The following users liked this post:
Rich Firth (03-27-2019)
#4
We have many customers use the Bav Technic software as it is affordable and will do it.
https://www.waymotorworks.com/bavari...-software.html
https://www.waymotorworks.com/bavari...-software.html
Last edited by IDoSeaDoo; 07-30-2018 at 10:44 AM.
#7
Trending Topics
#8
It gets locked in the dongle.
The latest software update for the Creator scan tool can reset adaptives also. You can find it HERE for $76
You have to reset them all individually but it's cheap and easy.
The latest software update for the Creator scan tool can reset adaptives also. You can find it HERE for $76
You have to reset them all individually but it's cheap and easy.
#9
The following 2 users liked this post by downshift1:
ECSTuning (08-07-2018),
Rich Firth (03-31-2019)
#13
So the trick was, you had to have the car running. I tried to update my Creator tool, and it updated the OBD part, but not the BMW part. That one kept failing. However, I was able to go into the Adaptations and clear them. It asked me if I'm sure, and gave me some other warning. Then it just cleared them and said "Done". However, I did not notice a difference. The shift flare from 3-4 is still very much there.
Is there some sort of sequence you must do to set the new adaptations?
Is there some sort of sequence you must do to set the new adaptations?
The following users liked this post:
Rich Firth (03-31-2019)
#15
I have an R50. Will the Schwaben/Foxwell 510 reset the fuel adaptions? I have tried without success. If it can reset the adaptions on an R50 do you have a procedure?
I have code 2097 (post-catalyst O2 sensor was reading too rich) which I can't clear. I want to use this procedure below which was posted by joey1320.
for that code you don't replace any o2 sensor. the issue is with the adaptation values for the dme.your dealer will have to do the following since they have the proper diagnostic tools.
tell them to check/clear the code.
reset the adaptation values.
do a "quick delete" before disconnecting communication between diagnostic equipment and car.
disconnect the battery from the car.
do a battery reset- touch both connectors that go to the battery posts with with a wrench for a minute.
let battery sit disconnected for 1/2 hour.
reconnect battery.
check to see if code is gone.
if not then do it all over again and let the battery sit longer. maybe an hour.
the dme has to reset the amount of fuel it delivers to the engine, which is causing you "rich"code.
that should take care of it. good luck!
i just fixed a car with the same code today by doing this, so it should get you going.
I have code 2097 (post-catalyst O2 sensor was reading too rich) which I can't clear. I want to use this procedure below which was posted by joey1320.
for that code you don't replace any o2 sensor. the issue is with the adaptation values for the dme.your dealer will have to do the following since they have the proper diagnostic tools.
tell them to check/clear the code.
reset the adaptation values.
do a "quick delete" before disconnecting communication between diagnostic equipment and car.
disconnect the battery from the car.
do a battery reset- touch both connectors that go to the battery posts with with a wrench for a minute.
let battery sit disconnected for 1/2 hour.
reconnect battery.
check to see if code is gone.
if not then do it all over again and let the battery sit longer. maybe an hour.
the dme has to reset the amount of fuel it delivers to the engine, which is causing you "rich"code.
that should take care of it. good luck!
i just fixed a car with the same code today by doing this, so it should get you going.
Last edited by cosmo727; 09-24-2018 at 08:21 AM. Reason: More info
#16
#18
i see this as an old dead post but in case someone comes along with similar issue and since i have recently worked on my tranny, in order to fix the flare from 3-4 you would have had to adjust the N282 valve body selenoid pressure valve this is accessed through the tranny oil pan.. in your severe flare case you would turn the adjustment screw on it 2-3 turns counter clockwise this would increase the pressure and this would stop the flare. not sure how permanent this fix is I will try to update in a few months.in my humble opinion shift adapts resets would never fix a severe issue like that.cheers
Thread
Thread Starter
Forum
Replies
Last Post
sarge21rvb
Stock Problems/Issues
2
10-14-2017 12:18 PM
d454brisson
R56 :: Hatch Talk (2007+)
5
04-27-2014 01:31 PM
gknorr
How to
7
11-04-2013 11:11 AM