Black Gloss Mini Logo's?
 

I have seen these around on cars on here but havent been able to find where people are getting them or the covers for them.

Thanks in advanced.

This isn't a good photo, but maybe you mean something like this?

http://mini.sewellparts.com/accessor...2012/5346.html

I painted mine. Tape off the center part, use a razor to make a nice clean line, put on 3 or 4 layers of paint, let dry, peel tape off, ta-da! Use a decent glossy black paint. I even sprayed on two coats of rust-o-leum self-etching primer on the emblem first followed by the gloss black painter's touch paint.

Attachment 160147

Attachment 160148

Exactly what calforhelp has done is what i'm after.
However, may have to run a few test piece's if i going to DIY way.
But being lazy, i was just hoping to buy some haha

I'm gonna just plasti dip the emblem next Wednesday since I'm taking off the Cooper S.

What's the easiest way to get off the Cooper S? I guess more specifically, what's the best way in the winter time? I've removed emblems in the past but it's been in the dead of summer, so the added heat was an advantage

PS...I do not have a heat gun. Lol

Dental floss and a little heat from a blow dryer

Okay.....I live in Manhattan. Unless I can find a standard-type outlet on a street lamp/post, a blow dryer isn't going to work either. Pretty much anything requiring electricity to power it is out of the question.

Any other suggestions? Would very hot water work?....pretty much pour it over the letters slowly and then use the dental floss right after?

pouring hot water would work but i would also suggest to fill a bag (ziploc) with hot water so you can put it on the emblem.
Then just soak the glue with "goo gone" and your done

Just from experience, do NOT use the "goo Be gone" it's a different chemical compound and will damage the finish on a lot of the mini finishes. My husband tried to use that on my R53 dash from the airbag sticker and completely destroyed the finish on my dash.

Everyone I've talked to said use "goo gone"?

Detroit Tuned told me that when I do this, use a blow dryer, dental floss or something soft and easy that will take off the emblem of the "Cooper S". Then use "goo gone" and wipe it down. After that has been done begin to wax that whole area and might as well wax down the whole trunk while your at it.

I'm gonna do it next Wednesday with my buddy.

Right. Just make sure you don't accidentally pick up "goo Be gone" it's not the same. Major damage.

Looks great!

I Tried the Plasti-Dip method today and it simply just didnt work at all. I masked off aswell as i could but could seem to crack leaving a decent edge. Did read somewhere the people pull the tape off when its wet?

Mini Wings Emblem Cover
 

I bought my black emblem covers a little over 2yrs ago from Aesthetic Creations. They are a hard gloss black plastic that you just stick on over the original piece.

Slide1.gif

Spewing, I can't seem to find their site. Must have closed down.

Yes, you have to peel any tape you're using with plasti-dip while the stuff is still wet. If you do it after it dries, it'll just peel up the surrounding plasti-dip.

I didn't know Aesthetic Creations site disappeared. You may want to look on ebay, they have different types. http://www.ebay.com

http://www.ebay.com.au/itm/MINI-COOP...ht_4666wt_1144

Found these on ebay. So il just get them painted black gloss and the issue is sorted.

This is what your looking for! They look awesome!
http://mini.sewellparts.com/accessor...2007/5346.html

That's quite a bit more expensive than a carefully trimmed 2" square piece of frog tape and a can of black spray paint. It also won't look as good. All of those badge covers add a noticeable amount of depth to the emblem.

They are a little pricey, I give you that lol. But man do they look good! Its almost a black chrome, and personally I couldn't paint it to look as good.

Oh no, those OEM parts aren't too bad. I was talking about the eBay part BLK-MCS posted right above you.

For the miltek exhaust. can i just buy the exhaust and keep the original header or do I have to by the manifold header? would the sound be different?

They look nice but I'm not paying $250 especially for a $10 item.