The 2nd Gen Sprintex Owners Thread
Due to the original thread being 99% about the old unit and it's issues, I think it's time for a separate thread for the newer 2nd Gen units.
How to to determine if you have a second generation Sprintex? The fill plug located closest to the belt will actually be a dipstick instead of just a plug. Known issues carried over from the 1st generation kits: (Send PM if you have others) Issue: 1. Faulty Tensioner / Fix = Bytetronik / GPR Tensioner 2. Light oil consumption / Fix = Bytetronik Vented plug Known Belt Combinations: (Send PM if you have others) ATI 2% / Stock Pulley (15-16psi) / GPR Tensioner = Continental 6PK1388 ATI 2% / 64mm Pulley (17-18psi) / GPR Tensioner = Gates K060539 ATI 2% / 60mm Pulley (19-20psi) / GPR Tensioner = Unknown Pulley Options: 64mm and 60mm Pulleys available from KAVS Motorsports Here Oil Change Capacity: 111mL of 75w90 Gear Oil |
Are there any known issues with the gpr tensioner?
|
I've had mine on for a while now and the only issue I have is the stock dampener bushings which I'm replacing with Powerflex ones.
It has a few nice features, you can still use your factory tensioner tool, and it has a built in stop should you have a belt fail. |
What's the problem with the bushings? Just worn out?
|
The factory rubber bushings in the shock deteriorate quickly under hard use.
The powerflex have a lifetime warranty on them so it was the logical choice. |
Originally Posted by downshift1
(Post 4392583)
The factory rubber bushings in the shock deteriorate quickly under hard use.
The powerflex have a lifetime warranty on them so it was the logical choice. |
Originally Posted by CSP
(Post 4392613)
interdasting. Any vendors care to weigh in on this? The $300 upgraded tensioner still needs aftermarket parts? |
Originally Posted by CSP
(Post 4392613)
interdasting. Any vendors care to weigh in on this? The $300 upgraded tensioner still needs aftermarket parts? |
Added some additional info
|
Have a few GPR Tensioner on hand ready to ship. PM if interested.
https://www.northamericanmotoring.co...ex-sc-kit.html |
Installation
If you have an R53 that has never had its harmonic balancer changed you will not be able to install the GPR tensioner, its too tight, lifted lowered the engine, impossible especially with the damper installed on the GPR, I've installed countless of oem belt tensioners on the R53s without removing the engine mount but the damper wasnt on untill tensioners were in place, GPR is a touch bigger and its bearing part that connects to the supercharger is a one piece, getting it past the sprintex pulley impossible, instructions are for earlier version. I will be taking the never changed harmonic balancer off and it will be ok, just a pain in the butt for us with the never changed harmonic balancers...good luck, unit looks amazing cant wait to have it all done in a couple of days...2002 R53 version 2 Sprintex...
|
Installation completed
GPR tensioner successfully installed by removing oem still from factory harmonic balancer, the thick one, then replaced...i did have a rattle i thought from the oem tensioner that came with the Sprintex, but its another issue...did have oil light on so could be my oil pump...but anyways tensioner looks amazing car at idle sounds great, just while I push on the gas it starts rattling..,may even have loose chain...thanks bytetronik recommend the GPR performance tensioner
|
Originally Posted by Ellie1972
(Post 4511330)
GPR tensioner successfully installed by removing oem still from factory harmonic balancer, the thick one, then replaced...i did have a rattle i thought from the oem tensioner that came with the Sprintex, but its another issue...did have oil light on so could be my oil pump...but anyways tensioner looks amazing car at idle sounds great, just while I push on the gas it starts rattling..,may even have loose chain...thanks bytetronik recommend the GPR performance tensioner
|
Originally Posted by Ellie1972
(Post 4511949)
the rattle again is from the failed timing chain tensioner i replaced a month ago...thought id check that too and its frozen wedged...now i need to tackle that issue ffs...Happy New Year all
|
Originally Posted by Ellie1972
(Post 4512360)
Timing chain tensioner has been removed by taking the valve cover off and with a long screwdriver with care was pried out...ordered new one be here on Tuesday 7th Jan...then we really get to test out the GPR performance tensioner.....have the vented plug in place instead of the dipstick, gear oil 111mm is replaced and a new belt....GTi I'm looking for you hahaha
|
Originally Posted by Bytetronik
(Post 4513006)
The next thing you need is a good tune to make it go even faster ;)
|
All times are GMT -7. The time now is 12:08 PM. |
© 2024 MH Sub I, LLC dba Internet Brands