New '05 R53 Purple Haze owner
#52
Those are here: 63130395387
https://www.northamericanmotoring.co...some-help.html
Install PDF:
http://www.motoringfile.com/howto/Fog%20Lights.PDF
https://www.northamericanmotoring.co...some-help.html
Install PDF:
http://www.motoringfile.com/howto/Fog%20Lights.PDF
__________________
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
The following users liked this post:
audihere (07-30-2018)
#53
#54
OK, wasn't too happy with how the OEM black/white bonnet stripes went on using the dry method, so we yanked them off and started over. I had originally purchased some 3M wide black stripes and separate thin silver stripes for the bonnet (I didn't know I was getting separate pieces). We used the wet method tonight with great success! I'll get pics in the sun tomorrow.
#56
#59
#61
#63
The stripes look fantastic!!
__________________
Your Trusted Source For DIY and Parts
FREE SHIPPING over $99 click here
MINI Parts | DIY Help | Facebook | Twitter | Instagram | YouTube | Promos
888.280.7799 | 6am - 5pm PST
FREE SHIPPING over $99 click here
MINI Parts | DIY Help | Facebook | Twitter | Instagram | YouTube | Promos
888.280.7799 | 6am - 5pm PST
The following users liked this post:
audihere (07-30-2018)
#64
Installed the rear fog light last night. The car was pre-wired for it, so that was the easy part. We had previously added the 6 toggle switch panel with the rear fog toggle. We enabled the rear fog by coding the BC1 on our laptop. One nice surprise was when we turned on the fog light, the toggle switch had a little tiny light on it that we didn't even notice!
My son removing the old plug.
Fog lamp installed
Fog lamp turned on
I didn't even know there would be a tiny light in the rear fog toggle switch. We haven't added the front fogs yet.
My son removing the old plug.
Fog lamp installed
Fog lamp turned on
I didn't even know there would be a tiny light in the rear fog toggle switch. We haven't added the front fogs yet.
Last edited by audihere; 08-08-2018 at 01:43 PM.
#65
We installed the OEM factory alarm kit last night. Purchased the turn signal with integrated flashing red light also. Our car was totally pre-wired for the alarm so it went in pretty easily. We enabled the alarm by coding it with our laptop. The red light did not flash until after coding on ours. Most of the alarm related coding was already enabled, just had to change the one master alarm setting to Active. One piece of advice, don't over tighten the nut on the stud while mounting the siren! Tested it with a wave of the hand and boy it's loud! Very high pitched alarm.
Ultrasonic Sensor
New turn signal with red light.
Installing siren
Unraveling the tape to access siren connector
Old turn signal
Light flashing indicating alarm is armed!
Ultrasonic Sensor
New turn signal with red light.
Installing siren
Unraveling the tape to access siren connector
Old turn signal
Light flashing indicating alarm is armed!
The following users liked this post:
ECSTuning (08-08-2018)
#66
Awesome!
__________________
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
MINI Guru/ MINI Owner Since 2004 | NEW Lifetime Part Replacement | Local Pickup
Milltek | Genuine MINI | Forge Motorsport | NM Engineering | ECS Performance | M7 Speed
Customer Service Hours: 8am-8pm EST|Sales Team Hours: 8am-11pm | SAT 10am-7pm 800.924.5172
#67
Nice job on the alarm! I just installed the alarm stalk this weekend and my light flashes w/o the alarm, although it doesn't start flashing until a minute or two after the doors are locked. WIth the alarm does it start flashing right away?
A few questions on the install... did you need to use anything from the kit to install the ultrasonic alarm, or did the unit snap into the housing without the bracket? Also, with the car pre-wired, did you only use the siren and bracket, alarm stalk, ultrasonic detector, and programming? I've seen a factory alarm module, but I'm not sure if it's only for the pre-facelift cars.
Where did you get your programming cable and software?
Thanks!
A few questions on the install... did you need to use anything from the kit to install the ultrasonic alarm, or did the unit snap into the housing without the bracket? Also, with the car pre-wired, did you only use the siren and bracket, alarm stalk, ultrasonic detector, and programming? I've seen a factory alarm module, but I'm not sure if it's only for the pre-facelift cars.
Where did you get your programming cable and software?
Thanks!
#68
Nice job on the alarm! I just installed the alarm stalk this weekend and my light flashes w/o the alarm, although it doesn't start flashing until a minute or two after the doors are locked. WIth the alarm does it start flashing right away?
A few questions on the install... did you need to use anything from the kit to install the ultrasonic alarm, or did the unit snap into the housing without the bracket? Also, with the car pre-wired, did you only use the siren and bracket, alarm stalk, ultrasonic detector, and programming? I've seen a factory alarm module, but I'm not sure if it's only for the pre-facelift cars.
Where did you get your programming cable and software?
Thanks!
A few questions on the install... did you need to use anything from the kit to install the ultrasonic alarm, or did the unit snap into the housing without the bracket? Also, with the car pre-wired, did you only use the siren and bracket, alarm stalk, ultrasonic detector, and programming? I've seen a factory alarm module, but I'm not sure if it's only for the pre-facelift cars.
Where did you get your programming cable and software?
Thanks!
You probably won't need those 2 white plastic brackets for the ultrasonic sensor if you have the cover on the headliner, those 2 white pieces were already in my car (facelift 2005 S).
I believe there was a factory kit for pre-facelift cars that included the wiper stalk and separate tilt sensor to be wired with included harness (a huge job if you have to add the harness). Sounds like the siren now incorporates the tilt sensor. My '05 has the red light on the turn signal stalk since the yellow light is on the wiper stalk.
I got my programming cable on eBay. I think I posted a link to it earlier in this thread. I highly recommend this seller. It came with a 32Gb thumb drive that had EVERYTHING I needed on it including some VERY simple instructions (some sort of HTML web format) on how to code the car. Everything I was reading online was much more difficult to understand. I do now use NCS Dummy to help with the translations though.
#69
#70
I got a rear view mirror with Home Link and Auto Dimming on eBay. We installed it and the Home Link and Auto Dimming worked great, but the key fobs no longer worked with the car. We tried all the procedures to re-link the keys to the car, but nothing was working. After disassembling the new mirror, we found a lot of corrosion on the receiver PCB which killed it.
We were able to swap the old mirror's receiver PCB into the new mirror even though they weren't exactly the same. Got everything working! Bye Bye garage door remote.
New mirror with Home Link.
Inside old and new mirrors.
Both PCB's. Old one is corroded and not functional anymore.
We were able to swap the old mirror's receiver PCB into the new mirror even though they weren't exactly the same. Got everything working! Bye Bye garage door remote.
New mirror with Home Link.
Inside old and new mirrors.
Both PCB's. Old one is corroded and not functional anymore.
The following users liked this post:
ECSTuning (08-14-2018)
#71
We decided that before we put the new chrome trim and license plate holder on the bumper, it should be re-finished. Lots of dents and chips. While removing it, we found a lot of the associated trim and guard pieces were heavily damaged. Ordered a bunch of new parts. In the mean time can't really drive the car much.
#75