Windshield Seal Filler Strip
#1
Windshield Seal Filler Strip
I have my new seals fitted and put the glass back in for my front windshield and rear window. I also have the filler strip insertion tool - handle with diamond shape wire for opening up the seal to install the filler strip.
My question for those that have installed their own seals, glass, & filler strip is what is the right technique for installing the filler strip. I originally went to use my old seals and managed to tear the seal - probably in part due to its age. This was probably a blessing as I was trying to save some $$ and was probably a bad idea.
Now I am concerned about damaging the new seal and my first attempts to install the filler strip did not go well - can anyone help with some pointers on how best to accomplish the installation????
Thanks for any help!
My question for those that have installed their own seals, glass, & filler strip is what is the right technique for installing the filler strip. I originally went to use my old seals and managed to tear the seal - probably in part due to its age. This was probably a blessing as I was trying to save some $$ and was probably a bad idea.
Now I am concerned about damaging the new seal and my first attempts to install the filler strip did not go well - can anyone help with some pointers on how best to accomplish the installation????
Thanks for any help!
#2
#3
#4
2nd Gear
iTrader: (5)
Join Date: Oct 2005
Location: Massachusetts
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Read Punks post and watch the videos first.
I did it late this past winter without the benefit of that post. First, make sure its really warm when you work...trust me on that. Second, I used white lithium grease to lubricate the channel before insterting the strip. Messy but I found it worked a lot better than soapy water, windhshield cleaner, silicon spray. But maybe if I had not been doing this in like 35-40 degrees the less greasy methods might have worked. Also, it takes some elbow grease to get going but once its under way it goes fairly smoothly. The tool is funky and it takes a few tries to get a feel for how it works. I found at times I had to sort of work it side to side to get the strip down in the channel. It left some dents in the strip but those went away after we thawed out. Check the fitting as you go along, you likely will need at some points to partly pull it back out and re-do a section to get it properly fit down in the channel. When you begin, you should check the centering of the starting point at least till you round the first corner, as it will shift from pulling. Use a very sharp razor knife to cut the end when you are fully around for a nice tight fit. When done, use your fingernail or something very thin to work the lip of the rubber up over the strip where it is puckered. Then clean it up and admire your good work!
I did it late this past winter without the benefit of that post. First, make sure its really warm when you work...trust me on that. Second, I used white lithium grease to lubricate the channel before insterting the strip. Messy but I found it worked a lot better than soapy water, windhshield cleaner, silicon spray. But maybe if I had not been doing this in like 35-40 degrees the less greasy methods might have worked. Also, it takes some elbow grease to get going but once its under way it goes fairly smoothly. The tool is funky and it takes a few tries to get a feel for how it works. I found at times I had to sort of work it side to side to get the strip down in the channel. It left some dents in the strip but those went away after we thawed out. Check the fitting as you go along, you likely will need at some points to partly pull it back out and re-do a section to get it properly fit down in the channel. When you begin, you should check the centering of the starting point at least till you round the first corner, as it will shift from pulling. Use a very sharp razor knife to cut the end when you are fully around for a nice tight fit. When done, use your fingernail or something very thin to work the lip of the rubber up over the strip where it is puckered. Then clean it up and admire your good work!
#5
#6
I was told by someone who has done lots of Mini windshields that the best lubricant (don't laugh) is KY jelly. It's water based, cleans up easy, and, well, it's made to make things easier to insert.
#7
Trending Topics
#9
Thanks for all the help on this. Video sure makes it look easy... I just got home from a long business trip, so I will be trying to install the filler strip tomorrow.
Now I just have to select the right lubricant.... Perhaps, I should pick one where I get my $$'s worth and will get to use the extra for something else
Now I just have to select the right lubricant.... Perhaps, I should pick one where I get my $$'s worth and will get to use the extra for something else
#10
#11
Hey Capt, I Don't think that's the one he was referring to..
I bet he means the White lithium, That way he can refill any rechargeable batteries he has about the house! Yeah, that's it!
Let us know how it goes, this is on my long Mini list of To-Do's...
Where did you get your filler strip material?
I bet he means the White lithium, That way he can refill any rechargeable batteries he has about the house! Yeah, that's it!
Let us know how it goes, this is on my long Mini list of To-Do's...
Where did you get your filler strip material?
Thread
Thread Starter
Forum
Replies
Last Post
IQRaceworks
R50/R53 :: Hatch Talk (2002-2006)
51
10-10-2015 03:54 PM
patsum
R50/R53 :: Hatch Talk (2002-2006)
11
09-30-2015 02:20 PM
Nicefeet
R50/R53 :: Hatch Talk (2002-2006)
2
09-24-2015 06:53 PM